Wolverine Coatings Corporation

IllumiFlect 3031

admin — Tue, 13 Sep 2011 16:09:15 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

This specification covers requirements for a reflective coating supplied in a liquid form for use as a retroflector. The coating compound is comprised of resins, thinners, pigments, glass beads and various additives. The coating is available in Silver White, Bright White, Yellow, and Black. Blue, Green & Red are available upon special requests.

The coating should be applied over a white or off-white background for the true color to best show. As the IllumiFlect is mostly transparent, and is easily masked by a darker or colored background. The coating compound in a freshly opened, full container, shall show no grit, skinning, curdling, or excess pigment flotation and shall show no more settling or caking than may be easily re-dispersed with a paddle to a uniform consistency.

The previously unopened package of product shall meet all of the requirements specified herein for a period of one year, provided that the daily mean temperature of the ambient air at the storage location falls within the range of 35°F to 90°F and the peak ambient temperature does not exceed 115°F.

APPLICATION DATA SUMMARY

IllumiFlect must be mixed vigorously and thoroughly, preferably with a mechanical paint mixer or shaker until uniform throughout. However, hand stirring and shaking will do an adequate job. IllumiFlect will be in a semi-gel state as received; however, thinning is not normally recommended since mixing reduces the viscosity of IllumiFlect. If thinning is necessary it may be done very sparingly with VM&P Naphtha, mineral spirits, xylol or heptane as may be indicated under specific applications, up to a maximum of a half pint per gallon of IllumiFlect. If allowed to stand, IllumiFlect will return to the semi-gel state.

SURFACE PREPARATION

IllumiFlect is very similar to most paints, and preparation for application should follow standard practices. The surface must be clean and dry. Maximum durability will be obtained on surfaces which you have previously repainted with a high quality exterior alkyd enamel or alkyd primer (white or off-white). If a surface has been primed with paint the final paint coat must be thoroughly dried before the application of IllumiFlect. Application on cement or asphalt should include a white base coat/primer. The primer must be thoroughly dry before the application of IllumiFlect product. For continuous coat galvanized steel or for black iron, preparation should include a light crystalline phosphate coating. Aluminum surfaces which have been anodized, crystalline phosphate coated, or prepared with amorphous chromate-type coatings are generally satisfactory. For exterior grade fir plywood, sanding, cleaning and sealing are recommended. For more specific information, consult Wolverine Coatings Corporation or your authorized Wolverine representative.

PRIMING

Surface should be primed with a white or off-white quality primer for enamels before application of the reflective liquid. High density overlaid plywood, aluminum or continuous coat mill galvanized phosphate coated steel should be primed on the face surface only. Exterior grade fir plywood and black iron should be primed and then covered with at least one coat of high quality alkyd enamel on both sides and all edges.

SPRAY APPLICATION – GENERAL

When using hand spray guns you should apply IllumiFlect with a nozzle .087 inches in diameter using a pressure pot as follows:

Prepare IllumiFlect and the surface to be reflectorized as previously mentioned.
The spray gun should be held 6 to 8 inches from the surface to be sprayed and an even single coat should be applied until the area is uniformly covered. A properly adjusted spray gun will finely splatter the reflective material onto the application surface. When you have incomplete atomization this minimizes over-spray and gives best coverage and sharp edges.
The IllumiFlect coating should be heavy enough to be wet but not so heavy as to sag. If sagging occurs the coating is being applied too heavily and the gun should be moved faster when spraying. Maximum reflectivity, true daytime appearance, and opacity are achieved only when the coating is completely dry.
You will find that occasional agitation of the reflective liquid will provide a more uniform application.
Reflectivity of IllumiFlect may be checked by sighting down a flashlight held at eye level while standing at least 50 feet from the reflective surface in a darkened area. However, do not check the reflectivity until the IllumiFlect has dried completely.
Following the use of IllumiFlect all spray equipment, stencils, etc, should be cleaned thoroughly with mineral spirits or xylol. Spray applications on abutments, bridges, curbing, small panels, etc. IllumiFlect may be applied to properly prepared surfaces of this type by spraying. If application is made at temperatures below 50°F initial reflectivity of the coating will be lower. Best results will be obtained on applications made at room temperatures above 50 °F.

APPLYING ILLUMIFLECT TO LARGE PANELS BY SPRAYING

Maximum reflection may be obtained from IllumiFlect by force drying the coating at 250°F. Please see the instructions under “Drying”.
Spray the panels in a vertical position for best coverage. To keep over-spray minimized when you have more than one panel to do, put the edges of the panels almost together and trigger the gun at the end of each pass.
Sometimes for best results is may be necessary to thin IllumiFlect before use. However, never use other thinners or thin in excess of what has been previously mentioned.

HAND BRUSHING

Hand brushing of IllumiFlect should be done generally in non-critical applications on smooth surfaces or on rough textured or porous surfaces. The reflective coating should be applied in full even strokes with a good quality paint brush. Brushing is not recommended over large areas.

SMOOTH SURFACES

Best results can be obtained with a soft, fine bristle brush such as a muslin brush. Close range appearance may be somewhat uneven but reflection and appearance will be adequate at uniform and normal viewing distances.

HAND ROLLER COATING

Hand roller coating of IllumiFlect is recommended only for uses where close range appearance and durability are not of prime importance such as construction signs, temporary markings, etc. The coating will appear mottled at close range but will provide a very adequate uniformity of reflection and appearance at distances beyond 100 feet.

The surface to which IllumiFlect will be applied should be prepared as previously mentioned “Surface preparation”.
Apply IllumiFlect in the standard conventional manner with good quality dense fiber fleeced roller. To minimize mottled appearance, roll back and forth until liquid is quite evenly deposited and then roll carefully in one direction only perpendicular to first application.
Clean roller carefully with mineral spirits to recover IllumiFlect absorbed during application.

DIPPING

IllumiFlect must be agitated in the tank to maintain a constant viscosity. Viscosity depends on temperatures of IllumiFlect and the article being dipped and should be adjusted to provide a light even coat. Too high a viscosity results in too heavy a coating. Viscosity too low results in excessively light, streaked coatings.
Viscosity measurement should be taken on moving liquid in dip tank. If thinning is necessary to adjust viscosity mineral spirits should be used.
Dipped articles must be allowed adequate dipping time, generally 2 to 5 minutes before entering curing overran. For best results coatings should be forced cured at 200°F according to the schedule under “Drying”.

DRYING

IllumiFlect reflective liquid will dry to a tack-free surface in 1 to 2 hours under normal drying conditions. Coating may be forced dried according to the following schedule:

After 10 minutes air drying, use 24 hours air dry, or 2 hours at 150°F, or 1 hour at 200°F, or 30 minutes at 250°F. Under normal drying conditions these drying times will harden the coating sufficiently for handling, although additional air dry continues to harden the coating. After drying, opaque legends or pictorials may be applied to the reflective coating by roller coating embossed areas with standard enamel type colors. Heavy color lay is necessary to cover exposed lens surface. A clear finishing or varnish coat should NEVER be used over IllumiFlect. Loss of reflection will occur in any over-coated area of the reflective surface.

COVERAGE

As with any paint material the coverage obtained will vary depending upon the application, the applied, the method and the surface. Screen processed on smooth non-porous surface, coverage will be approximately 100 square feet per gallon. Spraying, brushing and dipping will generally result in a reduced coverage per gallon as will applications on rough textured or porous surfaces. Best results are obtained with a single 15 wet uniform mil coating. Coatings lighter than recommended will result in reduced brilliance and durability. However, heavier coatings than recommended will not provide a corresponding increase in brilliance, and may actually result in reduced brilliance. Maximum opacity and true daytime appearance are achieved only when the coating is completely dry.

STORAGE

llumiFlect should be stored in a cool, dry place below 90°F and should be used within one year of date of manufacture. The date of manufacture will be clearly marked on all labels so that you will be able to maintain proper rotation of your stock.

AVAILABLE COLORS:

WARRANTY

Wolverine Coatings Corporation warrants its products to be free from defects in material and workmanship. Wolverine Coatings Corporation’s sole obligation and Buyer’s exclusive remedy in connection with the products shall be limited, at Wolverine Coatings option, to either replacement of products not conforming to this Warranty or credit to the Buyer’s account in the invoiced amount of the nonconforming products. Any claim under this warranty must be made by the Buyer to Wolverine Coatings in writing within five (5) days of Buyer’s discovery of the claimed defect, but in no event later than the expiration of the applicable shelf life, or one year from the delivery date, whichever is earlier. Buyer’s failure to notify Wolverine Coatings of such nonconformance as required herein shall bar Buyer from recovery under this warranty.

Wolverine Coatings makes no other warranties about the product. No other warranties, whether express, implied, or statutory, such as warranties of merchantability or fitness for a particular purpose, shall apply. In no event shall Wolverine Coatings be liable for consequential or incidental damages. Any recommendation or suggestion relating to the use of the products made by Wolverine Coatings, whether in its technical literature, or in response to specific inquiry or otherwise, is based on data believed to be reliable; however, the products and information are intended for use by Buyers having requisite skill and know-how in the industry, and therefore it is for the Buyer to satisfy itself of the suitability of the products for its own particular use and it shall be deemed that Buyer has done so, at its sole discretion and risk. Variation in environment, changes in procedure of use, or extrapolation of data may cause unsatisfactory results.

LIMITATION OF LIABILITY

Wolverine Coatings Corporation’s liability on any claims based upon Wolverine Coatings Corporation’s negligence or strict liability, for any loss or damage arising out of, connected with, or resulting from the use of the products, shall in no case exceed the purchase price allocable to the products or part thereof which give rise to the claim. In no event shall Wolverine Coatings Corporation be liable for
consequential or incidental damages.

IntegraFlex 1921

admin — Tue, 28 Jun 2011 12:12:46 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

IntegraFlex 1921 Flexible Joint Sealant is a 100% solids, two-component polymer hybrid that will provide a resilient filler for expansion joints. IntegraFlex 1921 has excellent flexibility and provides exceptional adhesion characteristics. IntegraFlex 1921 is recommended for expansion joints in general industry as well as expansion joints of highways, bridges, airports, garages, and marine decks. IntegraFlex 1921 provides an excellent bonding surface for other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

See Application Instructions for complete information on surface preparation, equipment, environmental conditions, application procedures, and safety precautions. For conditions outside the specifications or limitations described, contact Wolverine Coatings Corporation for details.

SURFACE PREPARATION

Coating performance is directly related to the quality and degree of surface preparation. Prior to overcoating, all surfaces must be clean, dry, undamaged, and free of all contaminants. For more specific information, consult the surface preparation section contained in the Application instructions.

SAFETY PRECAUTIONS

Read the Material Safety Data sheet carefully before use. Safety precautions in the MSDS should be carefully followed during storage, handling and use. Improper use and handling can be hazardous to health and cause fire or explosion.

EnduraShield 2254

admin — Tue, 28 Jun 2011 11:44:53 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

EnduraShield 2254 is a High Solids two component aliphatic clear gloss hybrid urethane applied over an epoxy primer or used to recoat and existing epoxy or urethane floor. Added abrasion resistance is obtained with the optional High Wear additive and produces a satin finish.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

IntegraFlex 1922

admin — Fri, 17 Jun 2011 18:32:12 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

IntegraFlex 1922 Flexible Joint Sealant is a 100% solids, two-component polymer hybrid that will provide a resilient filler for applications where a resilient, flexible non-sag material is needed. IntegraFlex 1922 is an ideal choice for filling vertical expansion joints, and repairing vertical or overhead joints or cracks in concrete or masonry surfaces. IntegraFlex 1922 has excellent flexibility and provides exceptional adhesion characteristics. IntegraFlex 1922 provides an excellent bonding surface for other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

OrganiClean 935

admin — Fri, 17 Jun 2011 15:51:29 +0000

	General Brochure
	Product Datasheet
	MSDS

	Architectural Specs

PRODUCT DESCRIPTION

OrganiClean 935 Industrial cleaner/degreaser is a concentrated multi-purpose cleaner/degreaser that has been designed to tackle difficult cleaning jobs. Formulated using a dynamic blend of surfactants, wetting agents, and natural citrus and soy solvents, OrganiClean 935 will quickly remove oil and grease that other cleaners cannot touch. It is designed to safely trap and change the chemical structure of grease, oils, pet stains, soap scum, ink, protein stains, etc., allowing them to be rinsed away with water. It can be used full strength for tough degreasing jobs or diluted with water for easier jobs.

FEATURES AND BENEFITS

Versatile: Multi-Purpose cleaner, degreaserand deodorizer
Concentrated: Use full strength for tough jobs or dilute for easier jobs
Economical: Can be diluted with water to maximize your dollars
Safe: Biodegradable water-based formula, that rinses away dirt, grime and odors.

RECOMMENDED USAGE

Degreasing
Factory and Warehouse floors
Garage and Concrete floors
Driveways
Farm Equipment
Trash Cans
Lawn Equipment
Engines
Tires
Appliances
Grills
Ovens
Toilets
Carpets and Textiles

LiquaTile 1142

admin — Fri, 17 Jun 2011 14:16:12 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LiquaTile 1142 is a 100% solids, AHC (Advanced Hybrid Cycloaliphatic) amine-cured self leveling epoxy floor coating which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures while also displaying outstanding mechanical properties, such as adhesion and abrasion resistance. It is a full ceramic version of LiquaTile 1184. LiquaTile Epoxy Floor Coatings are designed for concrete service such as warehouse flooring, machine pads, pharmaceutical processing areas, USDA inspected facilities, and chemical processing areas.

LiquaTile 1142 is available in four different formulations:

LiquaTile 1142 UVR (Increased UV Resistance)
LiquaTile 1142 UVR-FC (UVR with Faster Cure)
LiquaTile 1142 CHR (Increased Chemical Resistance)
LiquaTile 1142 CHR-FC (CHR with Faster Cure)

APPLICATION DATA SUMMARY

LiquaTile 1142 is mixed on site and applied with a notched trowel, squeegee, roller or airless spray to create a smooth, glossy floor. LiquaTile 1142 can also be applied to properly prepared steel surfaces without the need for surface primers or other types of secondary bonding agents in most cases.

SURFACE PREPARATION

Coating performance is directly related to the quality and degree of surface preparation. Prior to overcoating, all surfaces should have been properly prepared and primed, must be clean, dry, and free of all contaminants. For more specific information, consult Wolverine Coatings Corporation or your authorized Wolverine representative.

SAFETY PRECAUTIONS

IntegraFlex 1980

admin — Fri, 17 Jun 2011 13:59:57 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

IntegraFlex 1980 Crack Bridging Membrane is a 100% solids two-component polymer hybrid that will bridge severely cracked concrete surfaces. IntegraFlex 1980 has excellent flexibility and dimensional stability with exceptional adhesion characteristics. IntegraFlex 1980 provides an excellent bonding surface for other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

VitraPrime 0501

admin — Fri, 17 Jun 2011 13:39:38 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

VitraPrime 501 is a bonding enhancer for vitreous substrates. This unique chemistry will chemically bond to vitreous surfaces and leave chemical bonding sites to allow chemical bonding of epoxy coatings to the treated surface. The treatment’s uses include the surface treatment of floors, manholes, sumps, and other areas where the adhesion of a coating to a vitreous substrate is suspect. VitraPrime 501 provides an excellent bonding surface for other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

See Application Instructions for complete information on surface preparation, equipment, environmental conditions, application procedures, and safety precautions. Specifiers should contact Wolverine Coatings Corporation to discuss specific scenarios.

SURFACE PREPARATION

SAFETY PRECAUTIONS

This product is flammable! Keep away from heat, sparks, or open flame. Use proper static grounding procedures. Read the Material Safety Data sheet carefully before use. Safety precautions in the MSDS should be carefully followed during storage, handling and use. Improper use and handling can be hazardous to health and cause fire or explosion.

AcryliSeal 3501

admin — Fri, 17 Jun 2011 12:40:01 +0000

	General Brochure
	Product Datasheet
	MSDS

	Architectural Specs

PRODUCT DESCRIPTION

AcryliSeal 3501 is a high performance Water-Based Nano-Polymer Acrylic Sealer which leaves a protective membrane on the concrete surface that both waterproofs and seals. It contains no silicones, waxes, or oils and does not fade, yellow, chip, or peel when applied properly. This coating is created with a new generation of NanoPolymer resin technology that creates a waterbased product that will outperform comparable solvent-based products. This acrylic sealer will have much higher resistance to most chemicals including solvents, gasoline, and brake fluid which would not normally be withstood by conventional acrylics. In addition, an extremely tough acrylic surface is formed that is remarkably blush resistant and has many special qualities. AcryliSeal 3501 penetrates deeply into the concrete pores providing unusual durability and protection. It will also enhance the color of integral colored concrete or exposed aggregate by giving it a “wet glossy” look. Treated surfaces shed water, dirt, soot and chemical contaminants to prevent staining and moisture damage to the matrix. Because of the unusual characteristics of this formulation, it may be used for many different applications.

BASIC USES

AcryliSeal 3501 is widely used on concrete substrates to protect against soiling by airborne contaminants or other materials, which by absorption would cause unsightly substrate discoloration. AcryliSeal 3501 offers surface protection, water repellency, and color enhancement.

Patterned/Stamped Concrete – It is particularly effective on textured patterned concrete surfaces where the irregular texture pattern readily traps dirt and other particles causing discoloration.

Decorative Polymer Concretes – Provides a high performance, tough, durable, protective, topcoat seal. Water-white; resists yellowing when exposed to sunlight. Enhances the color of surfaces and provides additional chemical and abrasion protection.

Concrete Pavers – Brings out color and protects paver from fading or color change due to weathering. Helps seal against spillage.

Lightweight Concrete Block – Penetrates into concrete block pores for in-depth protection against moisture. Retards the moisture exchange in concrete that brings soluble concrete salts to the surface.

Architectural Concrete – Reduces lime leaching which can etch tinted colored glass, aluminum, etc. Brings out the fresh wet look color of aggregates.

Common and Face Brick – Prevents stains from penetrating into the brick surface. Dried film provides protection against chemical attack and makes brick easer to clean.

ADVANTAGES

Brightens and weatherproofs exposed aggregate walls and sidewalk areas.
Dries hard. Will not attract dirt, airborne dust or grime.
Reduces moisture entry into concrete surfaces and helps prevent efflorescence.
Quick drying time. Dry to the touch in 30-40 minutes
Minimizes spalling of exterior concrete due to soft moisture absorbing aggregates or concrete.

PRODUCT LIMITATIONS

Do not apply to wet or damp surfaces, as this can cause poor bonding or blushing (milky white or frosty appearance). AcryliSeal 3501 is not to be used as concrete curing compound. Although AcryliSeal 3501 is a clear, non-yellowing film, any clear coating can change the light refraction characteristics of the surface giving the visual effect of a slight color change. Differences in porosity and non-uniformity of application on smooth masonry/concrete might affect the even distribution of AcryliSeal 3501.

Application will give the colored surface a gloss wet look and will generally deepen the color. It will accentuate color variations or trowel burns. Always coat a test area to determine acceptability and to assure desired aesthetic results. Some brick, color stuccos, mortars, and cements will bleed color when subjected to a Water-Based coating. On brick and colored masonry surfaces a test area is imperative to determine compatibility and adhesion.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

ChemShield 1883

admin — Fri, 17 Jun 2011 12:21:43 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

ChemShield 1883 is a sprayable, 100% solids, high functionality, A.H.C. (Advanced Hybrid Cycloaliphatic) Phenolic Novolac Epoxy lining which exhibits excellent resistance to organic solvents, caustic environments, and acidic exposures. ChemShield 1883 is well suited for sewage pipe, treatment plants, petroleum refining and storage, and chemical plants.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

Coating performance is directly related to the quality and degree of surface preparation. Prior to coating, all surfaces must be clean, dry, undamaged, and free of all contaminants. For more specific information, consult the surface preparation section contained in the Application instructions.

SAFETY PRECAUTIONS

LiquaTile 1143

admin — Thu, 16 Jun 2011 19:55:00 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LiquaTile 1143 is a 100% solids, AHC (Advanced Hybrid Cycloaliphatic) amine-cured self leveling epoxy floor coating which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures while also displaying outstanding mechanical properties, such as adhesion and abrasion resistance. It is a full ceramic version of LiquaTile 1184. LiquaTile Epoxy Floor Coatings are designed for concrete service such as warehouse flooring, machine pads, pharmaceutical processing areas, USDA inspected facilities, and chemical processing areas.

LiquaTile 1143 is available in four different formulations:

LiquaTile 1143 UVR (Increased UV Resistance)
LiquaTile 1143 UVR-FC (UVR with Faster Cure)
LiquaTile 1143 CHR (Increased Chemical Resistance)
LiquaTile 1143 CHR-FC (CHR with Faster Cure)

APPLICATION DATA SUMMARY

LiquaTile 1143 is mixed on site and applied with a notched trowel, squeegee, roller or airless spray to create a smooth, glossy floor. LiquaTile 1143 can also be applied to properly prepared steel surfaces without the need for surface primers or other types of secondary bonding agents in most cases.

SURFACE PREPARATION

SAFETY PRECAUTIONS

TrowelEase 1162

admin — Thu, 16 Jun 2011 19:39:58 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

TrowelEase 1162 is a 100% solids, two-component AHC (Advanced Hybrid Cycloaliphatic) epoxy mortar binder which exhibits excellent adhesion on concrete. The coating’s uses include epoxy flooring or concrete patching. TrowelEase 1162 can be used alone or can be topcoated with other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

Coating performance is directly related to the quality and degree of surface preparation. Prior to overcoating, all surfaces must be primed, clean, dry, undamaged, and free of all contaminants. For more specific information, consult the surface preparation section contained in the Application instructions.

SAFETY PRECAUTIONS

TrowelEase 1160

admin — Thu, 16 Jun 2011 19:23:41 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

TrowelEase 1160 is a 100% solids, two-component AHC (Advanced Hybrid Cycloaliphatic) epoxy mortar binder which exhibits excellent adhesion on concrete. The coating’s uses include epoxy flooring or concrete patching. TrowelEase 1160 can be used alone or can be topcoated with other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

BondTite 1101 Primer

admin — Wed, 08 Jun 2011 15:38:45 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

BondTite 1101 is a 100% solids, two-component AHC (Advanced Hybrid Cycloaliphatic) epoxy primer which exhibits excellent adhesion and sealing properties on steel or concrete. The coating’s uses include the priming of floors, manholes, sumps, and other areas until overcoating can be completed. BondTite 1101 provides an excellent bonding surface for other Wolverine Coatings Corporation products. In addition, BondTite 1101 can also be used as a clearcoat or a clear broadcast medium for decorative finishes.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

BondTite 1105 Primer

admin — Sun, 05 Jun 2011 20:39:48 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

BondTite 1105 is a 100% solids, two-component epoxy primer which exhibits excellent adhesion and sealing properties on steel, dry or damp concrete, Expanded Polystyrene, and other foam type products. The coating’s uses include the priming of manholes, sumps, and other difficult-to-dry areas until overcoating can be completed. BT 1105 provides an excellent bonding surface for Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

BondTite 1109

admin — Thu, 02 Jun 2011 14:24:33 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

BondTite 1109 is a 100% solids, two-component AHC (Advanced Hybrid Cycloaliphatic) epoxy primer which exhibits excellent adhesion and sealing properties on steel or concrete. The coating’s uses include the priming of floors, manholes, sumps, and other areas until overcoating can be completed. BondTite 1109 provides an excellent bonding surface for other Wolverine Coatings Corporation products. In addition, BondTite 1109 can also be used as a clearcoat or a clear broadcast medium for decorative finishes.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

LiquaTile 1184 TopCoat

admin — Wed, 04 Mar 2009 02:44:15 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LiquaTile 1184 TopCoat is a 100% solids, amine-cured self leveling epoxy floor coating which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures while also displaying outstanding mechanical properties, such as adhesion and abrasion resistance. LiquaTile Epoxy Floor Coatings are designed for concrete service such as warehouse flooring and machine pads.

APPLICATION DATA SUMMARY

LiquaTile is mixed on site and applied with notched trowel, “squeegee”, roller or airless spray to create a smooth, glossy floor. LiquaTile can also be applied to vertical and horizontal steel surfaces without the need for surface primers or other types of secondary bonding agents in most cases.

SURFACE PREPARATION

Coating performance is directly related to the quality and degree of surface preparation. Prior to overcoating, all surfaces must be clean, dry, primed, and free of all contaminants. For more specific information, consult Wolverine Coatings Corporation or your authorized Wolverine representative.

SAFETY PRECAUTIONS

TrowelEase 1161

admin — Wed, 04 Mar 2009 02:41:27 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

TrowelEase 1161 is a 100% solids, two-component AHC (Advanced Hybrid Cycloaliphatic) epoxy mortar binder which exhibits excellent adhesion on concrete. The coating’s uses include epoxy flooring or concrete patching. TrowelEase 1161 can be used alone or can be topcoated with other Wolverine Coatings Corporation products.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

LiquaTile 1183 TopCoat

admin — Wed, 04 Mar 2009 02:39:00 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LiquaTile 1183 is a 100% solids, amine-cured self leveling epoxy floor coating which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures while also displaying outstanding mechanical properties, such as adhesion and abrasion resistance. LiquaTile Epoxy Floor Coatings are designed for concrete service such as warehouse flooring and machine pads.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

LiquaTile 1183 GF

admin — Wed, 04 Mar 2009 01:36:37 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

ChemShield 1183 GF is a sprayable, 100% solids, amine cured novolac epoxy lining which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures. The integration of flakeglass reinforcements also gives the coating excellent resistance to permeation and very good abrasion resistance. ChemShield 1183 GF is well suited for sewage pipe, treatment plants, petroleum refining and storage, and chemical plants using mineral acids such as phosphoric acid plants, hydro metallurgy, and metal plating facilities.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

LiquaTile 1171 TopCoat

admin — Wed, 04 Mar 2009 02:29:09 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LiquaTile 1171 is a 100% solids reinforced, proprietary formulated epoxy-based lining designed for corrosion control and protection of tank internals and any other areas requiring approval for potable water or USDA authorization. LiquaTile 1171 has been tested and certified by NSF under Standard 61 for use in potable water tanks. LiquaTile 1171 is also USDA authorized for use in Federally Inspected meat and poultry plants where there is a possibility of incidental food contact. This product is intended for industrial use only.

TYPICAL USES

Steel and fiberglass storage tanks or pipelines
Harsh/Severe Industrial Maintenance Applications
Tank Linings including potable water
Chemical process floors & concrete containment areas
Pulp and Paper Services
Waste Pits
Wastewater Treatment Applications

BENEFITS

Fast Turnaround time (Cures in 12 hours at ambient temperature)
Flexible to reduce coating stress caused by “oil canning” effects
High-build, easy to install monolithic application process (12-16 mils WFT/DFT per coat)
Excellent adhesion to steel, concrete and fiberglass substrates
Low cured shrinkage
VOC compliant (Solvent Free)

LineGevity 454

admin — Wed, 04 Mar 2009 02:25:42 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LineGevity 454 is a propriety 100% solids, internally reinforced, self leveling, AHC Polymer designed specifically for the application of lines on warehouse and factory floors. LineGevity 454 exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures while also displaying outstanding mechanical properties, such as adhesion and abrasion resistance. LineGevity Line Coatings are designed for concrete or metal flake floors and is self priming on steel.

APPLICATION DATA SUMMARY

LineGevity 454 is mixed on site and applied with notched trowel, “squeegee”, roller or airless spray to create a long lasting abrasion and wear resistant line. LineGevity can also be applied to vertical and horizontal steel surfaces without the need for surface primers or other types of secondary bonding agents. A primer must be used on concrete surfaces.

SURFACE PREPARATION

SAFETY PRECAUTIONS

LineGevity 302

admin — Wed, 04 Mar 2009 02:23:26 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

LineGevity 302 is a propriety 100% solids, internally reinforced, self leveling, AHC Polymer designed specifically for the application of lines on warehouse and factory floors. LineGevity 302 exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures while also displaying outstanding mechanical properties, such as adhesion and abrasion resistance. LineGevity Line Coatings are designed for concrete or metal flake floors and is self priming on steel.

APPLICATION DATA SUMMARY

LineGevity 302 is mixed on site and applied with notched trowel, “squeegee”, roller or airless spray to create a long lasting abrasion and wear resistant line. LineGevity can also be applied to vertical and horizontal steel surfaces without the need for surface primers or other types of secondary bonding agents. A primer must be used on concrete surfaces.

SURFACE PREPARATION

SAFETY PRECAUTIONS

EnduraTread 1191

admin — Wed, 04 Mar 2009 02:20:46 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B \| Part C
	Architectural Specs

PRODUCT DESCRIPTION

EnduraTread 1191 is a thick-film, 100% solids, proprietary formulated epoxy-based rubberized compound designed to protect surfaces from heavy impact. EnduraTread 1191 may also be used on floors in areas where protection is needed for employees standing for long periods of time. EnduraTread 1191 is trowel-applied from 125-2000 mils DFT depending on the level of protection desired, and is flexibilized to reduce coating stress resulting from mechanical and physical forces exerted on the substrate. The rubber is functionally treated to react into the system to prevent pre-mature failure. EnduraTread XP-1191 is a two-component system; Resin and Hardener.

TYPICAL USES

Inmate weightlifting areas
Process floors & concrete areas
Pulp and Paper Services
Loading Docks

BENEFITS

Fast Turnaround time (Cures in 12-36 hours at ambient temperature)
Superior wide range chemical resistance
High abrasion resistance
Flexible to reduce coating stress caused by substrate movement and impact
High-build, monolithic application process (125-2000 mils DFT) (1/8 inch – 2 inches)
Excellent adhesion to primed steel, concrete and fiberglass substrates
Low cured shrinkage
VOC compliant

ChemShield 5631

admin — Wed, 04 Mar 2009 02:01:11 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

These unique high performance coatings are heavy duty chemically resistant systems for protection against general chemical exposures and immersion service. ChemShield 5631 utilizes 1/32 inch chemical grade glass flakes, thus offering the desired flexibility, impermeability, application time, and abrasion resistance for maximum performance.

TYPICAL APPLICATIONS

ChemShield 5631 provides excellent chemical resistance and corrosion protection for areas in refineries, petrochemical, petroleum and hydrocarbon storage, chemical processing and pulp mills.

CHARACTERISTICS

The ChemShield 6100 Series is a custom designed coating system that is suitable for specific environmental exposures. The flake glass content provides a low vapor transmission rate with 7.7 times more protection than normal Vinyl Ester Coatings. This gives the coating an extremely high corrosion and chemical resistance in recommended uses. This material is suitable for high solvency and/or high temperature performance. Usage examples include tall oil, super unleaded gasoline, pulp mill red/black liquor, ethyl alcohol, and crude oil. User friendly CS6100 Series is easily repaired by recoating.

ChemShield 5232

admin — Wed, 04 Mar 2009 01:58:07 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

These unique high performance coatings are heavy-duty chemically resistant systems for protection against general chemical exposures and immersion service. ChemShield 5232 utilizes 1/64-inch chemical grade glass flakes, thus offering the desired flexibility, impermeability, application time, and abrasion resistance for maximum performance. Other 5200 Series Products Include sealer and putty. This formula is available in winter (low temperature) and summer (high temperature) versions for extreme conditions.

TYPICAL APPLICATIONS

ChemShield 5232 can be used for structural steel protection, steel maintenance coating, helicopter pads, offshore structures, and for protection against salt-water spray.

CHARACTERISTICS

The ChemShield 5200 Series is a custom designed coating system that is suitable for specific environmental exposures. The flake glass content provides a low vapor transmission rate with 7.7 times more protection than normal Isophthalic Polyester Coatings. This gives the coating an extremely high corrosion and chemical resistance in recommended uses. User friendly ChemShield 5232 Series is easily repaired by recoating.

ChemShield 1881

admin — Wed, 04 Mar 2009 01:53:00 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

ChemShield 1881 is a sprayable, 100% solids, A.H.C. (Advanced Hybrid Cycloaliphatic) Phenolic Novolac Epoxy lining which exhibits excellent resistance to organic solvents, caustic environments, and acidic exposures. ChemShield 1881 is well suited for sewage pipe, treatment plants, petroleum refining and storage, and chemical plants using mineral acids such as phosphoric acid plants, hydro metallurgy, and metal plating facilities.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

ChemShield 1836

admin — Tue, 03 Mar 2009 22:20:28 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

ChemShield 1836 is a sprayable, 100% solids, amine cured novolac epoxy lining which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures. The integration of flakeglass reinforcements also gives the coating excellent resistance to permeation and very good abrasion resistance. ChemShield 1836 is well suited for sewage pipe, treatment plants, petroleum refining and storage, and chemical plants using mineral acids such as phosphoric acid plants, hydro metallurgy, and metal plating facilities.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

ChemShield 1831

admin — Tue, 03 Mar 2009 17:25:44 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

ChemShield 1831 is a sprayable, 100% solids, A.H.C. (Advanced Hybrid Cycloaliphatic) Ceramic Phenolic Novolac Epoxy lining which exhibits excellent resistance to organic solvents, caustic environments, and dilute acidic exposures. The integration of flakeglass reinforcements also gives the coating excellent resistance to permeation and very good abrasion resistance. ChemShield 1831 is well suited for sewage pipe, treatment plants, petroleum refining and storage, and chemical plants using mineral acids such as phosphoric acid plants, hydro metallurgy, and metal plating facilities.

APPLICATION DATA SUMMARY

SURFACE PREPARATION

SAFETY PRECAUTIONS

ChemShield 1683

admin — Tue, 03 Mar 2009 17:23:01 +0000

	General Brochure
	Product Datasheet
	MSDS Part A
	MSDS Part B
	Architectural Specs

PRODUCT DESCRIPTION

ChemShield 1683 is a thick-film, 100% solids reinforced, proprietary formulated epoxy-based internal lining designed for corrosion control and abrasion resistance in chemical plants, and any other areas requiring excellent chemical resistance in immersion conditions. ChemShield 1683 may also be used for restoration and leak prevention of petroleum storage tank bottoms and pipelines where resistance to abrasion is needed. ChemShield 1683 is spray-applied from 40–125 mils DFT depending on the extent of corrosion, and is flexibilized to reduce coating stress resulting from mechanical and physical forces exerted on the substrate. ChemShield 1683 is a two-component system; Resin and hardener.

TYPICAL USES

Steel and fiberglass storage tank bottoms or pipelines
High temperature tanks and process vessels
Pipe internals carrying slurries & abrasive mixtures
Chemical process floors & concrete containment areas
Pulp and Paper Services

BENEFITS

Fast Turnaround time (Cures in 24 hours at ambient temperature)
High abrasion resistance
High-build, easy to install monolithic application process (40-125 mils DFT)
Excellent adhesion to steel, concrete and fiberglass substrates
Low cured shrinkage
VOC compliant

CHEMICAL RESISTANCE

Summarized; for a more comprehensive list of chemical resistance, please refer to our Product Resistance Data Guide. Films cured for 7 (seven) days at 77ºF are unaffected after 1 (one) year immersion at ambient temperatures.

Alum
Aluminum Chloride, 29%
Bleach
Lactic Acid, 10%
Sulfuric Acid, 70%
Sodium Hydroxide, 50%
Trichloroethane
Water, distilled
Xylene